• Contents User's Manual Reasons to choose Steelmate ----------------------- 17. Valet (service mode)---------------------------------- 18. Emergency override ---------------------------------- Important notice ------------------------------------------ Brief look at transmitters ------------------------------ 19. Turbo timer mode (F1, F19, F21)------------------ 20. Transmitter operation range indication----------- About LCD screen --------------------------------------- 21. • Reasons to choose Steelmate Important notice Brief look at transmitters * Please install the system by an authorized 1. Professional manufacturer with German quality standards. One piece 337 download. Antenna Disarm * Keep the product and the transmitters away from 2. Complete range of products, you can easily water. • About LCD screen Battery indicator System operation The battery status of the LCD transmitter will Button Button function Button function optional be shown on the LCD display. Lock doors & arm the system Press and hold for 2 seconds to arm in mute mode (with siren turned off for one arm cycle) When the battery indicator is empty, the transmitter needs to be charged immediately. • Status indication Functions 1. Arming operation If the door or trunk is not closed properly after arming Parking lights flashing table LED indicator flashing table To arm the system, press transmitter button: the system, the siren will chirp 3 times with the 1) 1 flash --- system armed 1) Fast flashing---passive arming mode The siren will chirp once. • F4/1: Doors will not be unlocked when the ignition once, the hour digit will flash, then press button, turns off. The flashing icon will change in the sequence below: time/hour time/minute alarm on/off alarm/hour F4/2: Doors will be unlocked automatically when the alarm/minute W-mode setting exit. May 28, 2018 - 地址:广东省中山市东凤镇东阜路和平大道铁将军工业园邮政编码:528425 电话:076. Steelmate 898g Car Alarm Manual rolled out are. 3 Congratulations on your wise choice of Steelmate Car Alarm System! It is highly recommended you read this manual carefully before using of this unit. Arming without transmitters engine will be blocked periodically. If you place the transponder card in the working If door is opened and stays open, then the system Press valet switch once, then press and hold it 3) 40 seconds later, the siren will chirp with parking will delay transponder card searching for 4 minutes. Turbo timer mode (F1, F19, F21) 24.1. How to enter the personal code: transmitter shows that the transmitter is within the 10 seconds, the siren will chirp accordingly. Turn The time can be programmed (F1). Turbo timer Disarm system, turn ignition off and wait for 5 operation range of the system. • F12 - personal code System will enter the F1 programming mode (LED Switch off the power of the transponder card (if will flash once after one pause). ![]() ![]() Available) In programming mode, the number of times LED Follow the steps of 'How to enter the personal flashes is corresponding to the function number. • System programming table Continued Function Description 1 chirp 2 chirps 3 chirps 4 chirps 5 chirps System programming table Restore factory setting Function Description 1 chirp 2 chirps 3 chirps 4 chirps 5 chirps Programming the function F12- F25 depends on the mode of F12, 'valet mode' or 'personal Press button Press button Press button. • Continued F3/4: the doors will be locked when footbrake is to turn on device, such as releasing trunk. Function Description 1 chirp 2 chirps 3 chirps 4 chirps 5 chirps pressed (by F25) automatically. F8/2: the blue wire will output signal (-) for 30 The system will not lock the doors if any door is seconds to roll up windows. • Installation instruction F11 Restore factory setting: F16 Anti-hijack by transmitter F21/2: output signal (-) for turbo timer according to Before you begin the installation * Read the INSTRUCTIONS! This option allows the system to restore the factory To activate the anti-hijack by pressing transmitter the time of the F1 setting. • * BLUE/ RED WIRE - INST2 input (-). * YELLOW WIRE -- vehicle or through the grill. Face the siren down so IGN1, +12V ignition input. Plug in connectors that water cannot accumulate inside the siren bell. Connect to hood pin switch or trunk switch. Connect to a main ignition wire at the ignition switch 2-Pin Connector: Plug-in connector port for LED. • Door lock wiring diagrams Optional relay wiring diagrams N N E E G G A A T T I I V V E E P P U U L L S S E E L L O O C C K K S S Y Y S S T T E E M M A A D D D D I I N N G G A A C C T T U U A A T T O O R R S S (-) DOOR LOCK (-) DOOR UNLOCK. • Wiring diagram Troubleshooting Fault Causes 1. The continuous chirping of the siren cannot The plug is improperly inserted.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |